Power of a skirting heating system:

Electric plinth – 200 W per linear metre.

Water plinth – 200 W per linear metre at coolant temperature 65°

Accordingly, when the temperature of the coolant increases, the power increases proportionally. For example, at 80° it will be 270 W per linear metre Since such an increase in temperature in the middle strip of Russia is possible only in the emergency case, when frost on the street 40-50°, the increase in temperature of the coolant leads to the formation of increased convection, and the meaning of plinth heating is lost.

Warm water plinth uses 0.34 l of water per 1 meter, and one complete circuit of water heating system with length of 12.5 m – only 4.5 l, which provides high dynamism and rate of heating.

The heat carrier volume is only 8 litres in the room heating system in 100 m2.

Sizes of a heating plinth

• A of 140 mm. Height of the wall mounted article
• B of 30 mm. Plinth depth
• From 60 mm. Height of the heating module
• D 13 mm. Diameter of a copper tube
• E of 25 mm. Depth of the heating module
• F of 2500 mm. Length of single heating module MAX

The construction of the Thermal Plinth uses materials with a high coefficient of thermal conductivity: copper, brass, aluminium, uncoated corrosion, which implies high reliability and guarantees a long service life.

General complete set of a system:

• Heating module made of two copper tubes with brass lamellae.
• Aluminium housing consisting of upper, lower and closing strips
• Tapes: heat insulation and heat reflecting
• arms for fastening of the heating module, a fixing set.

Materials have no harmful effects on the environment, are completely safe for humans and pets. There are no odors when heated.

 

The Warm Plinth system is certified. (Certificates and responses)

The system successfully passed the tests at the industrial site with a pressure in the heating pipes of 30 atm, Certified for residential use, where the system operates at 15-20 atm. In private construction, Where there is no high pressure in the heating pipes, the coupling is allowed, Consisting of brass bushing with external thread and two nuts, Rubber sealing ring and brass cone washer are fitted in inner part of said ring. However, a soldering joint is required to use the system in pressurized objects.

Where else can heat radiation be found?

In spring, when the sun starts to warm up, how nice it is to warm up under its rays, even if snow lies around, and the temperature is negative, you feel its warm affectionate rays – its radiant heat. A warm plinth creates the same heat effect as the sun.

Sitting at the bonfire, you sense direct invisible heat rays coming from it when the air around is cold. The principle of operation of the Russian furnace is also based on heat radiation. A Turkish bath where the air is not hot, the bath effect is achieved by radiant heat from warm stone walls.

A person is much more comfortable indoors with warm walls and cool air than with hot air but cold walls. Despite the normal air temperature in the unheated house, people do not leave a feeling of cold – naughty, uncomfortable. In order not to be cold, the air temperature in the room tries to keep above 20-22 ° – only in this case the temperature of the external walls can rise to an acceptable-comfortable temperature.

Warm plinthus act on the principle of energy conversion to thermal radiation.

In the Warm plinth heating system, heat from a heating element mounted directly into the plinth rises very slowly along the walls, heating their surface (Coanda effect).

Warm walls transfer heat to indoor objects and directly to you. Precious heat is contained in structures, not in air, and does not come out with air during ventilation and ventilation.

The amount of oxygen does not decrease, the optimum humidity is maintained and the air does not become dry. A room heated by a thermal lens retains heat for a long time by exposing surrounding objects rather than air to heat rays.

Do you still think what heating system to install in the house?

The heating system shall, if possible, be:

• energy efficient and economic. Energy efficiency and cost-effectiveness of the heating system are the application of technologies that minimize the cost of all types of energy by reducing its consumption. Saving heat, electric energy is not a rejection of comfort in a private house or apartment, but a provision of rational use of energy. Given the steady rise in energy tariffs, the need to save energy comes to the fore. For every extra litre and every extra kilowatt, you have to pay a high price.
• reliable and durable. The repair of any heating system is a very painful procedure, and the complete replacement of heating pipes of the warm floor system by the degree of disaster is equivalent to a fire. Reliability of plinth heating system consists in its accident-free and high repairability.
• Have stable hydraulic characteristics and thermal stability The modern heating system shall have technical control capabilities and predictability of coolant flows in pipes.

All these characteristics are answered by the system – Warm Plinth